To identify errors washing machine or dishwasher before calling a technician

I am a washing machine, dishwasher and dryer laundry engineer and my clients are usually pretty good at explaining what the error is. However, some more advice from the technical point of view enough to help you as a customer, to help me find a fault quickly. It could be very useful if as much information as possible, because the build-up when the car started to go wrong. If the error description is not right, is simply wrong to the end of MassWaste problem and a lot of time. (A classic case go to the moon to get your good ..... I'll leave that one!). It is sometimes difficult, because you turn it on and feet, and you do not notice anything until things go wrong terribly obvious. Take your time and watch carefully what happens and at what time its success.

Before calling a technician, there are some simple tests you can do what he can not only help an engineer, if you only have one, but you never know what might be calledAvoid it altogether. There are obvious error, the cause. If the machine is full of water and not draining, (this also produces other symptoms, the machine will do the laundry around the end of the wash cycle, is not the function of rotation, what is wrong with the very fact that there is water still in the drum stops, turns). Try this, some machines have only a function of discharge, this avoids any noise passes through something else, like turning the drum, for example, ifthere is no workload only, select a ride and it took a couple of minutes until the drum starts to rotate in the meantime you should hear the churning sound of the drain pump. Have you heard anything? No! then the drain pump does not work. If it's a yes! Then there is a blockage somewhere.

Hose Timer

On the other hand, if something happens when you turn, some machines have some form of "power on" turns on lights when you press the power switch then there is no powerto drive. Check the power outlet, the machine uses a table lamp into the outlet and see if you have the power to the machine. Otherwise, check the fuse in the plug sounds, of course, but it's worth. If you have the power to the machine then maybe its the door switch on the door of the machine, either as an engineer for the call.

If it is incredibly rude and pour water all over the floor (you have is the deluxe model, then ..cleans the floors as well!). Turn off all water taps as the (usually under the sink) for the machine and unplug the power cord, then call someone. This also applies to the safety switch of the machine blowing fuses, or intervention and electricity. What I mean is this error that the machine works, but then you hear something or not doing what it should be. Try a couple of things first, the timer at the same point in the cycle stop? Of electro-mechanical timer (identify this type ofAs the dial with your program and click a latching mechanism, such as slices, and turns, with the advance of the wash cycle). When it stops, or the machine running for an indefinite time to do the same function with the timer just stick to the same place, or do you have to set the timer goes on in one click click and the machine. Before you do this, highlight with a pencil on the dial and the corresponding part of the panel. Then the engineer can be the exact time ofError. This type of disorder can be a source of heat or a problem with the timer.

But thanks to modern technological advances, mechanical timer is replaced by electronic control devices, so you can not, at what point the program to see. Although some have a program-timer LED display, note the time, the display has the appearance of disorder (in advertising or anything for that matter) and the program you use. Some of them coughing up error codes on the LED display, thisbe given to a limited extent in the operation manual, but usually are not very extensive. The only thing you can do here (again, first program the machine to write what went wrong one) is to launch a new program, try this time, however, a 'fast' and the shortest program Washing can be found on the washing machine when its dishwashers try once a program of 'Quick', if its got one. Do not look for the "Rinse", because the hot water and heating may be to blame.Time, like going along in the cycle before it stops or goes wrong, or sometimes when not bad at all. To an engineer, this could help eliminate a couple of things. If you think that you can not water in a washing machine or dishwasher, simply loosen the hose connection on the back of the machine (not complete separation) and see if the water passes through. Unfortunately, it requires the machine to get rolling on the back for doing this.If you do not check the control valve is turned off. Surprisingly, and not infrequently, the valve can be turned off in the car, for example, if you only a plumber for a job (or husband), perhaps a little 'work under the sink and password, open the tap on again .

If you did everything you have done two things. You have the possibility that there is something very easy to remove and you may be able to resolve on its own, that saved aEngineers call. It can also, if it turns out, not to the device and an electrical problem has become home, not from the power outlet, for example, in which case you call an electrician. Or, if you call a water problem, you call a plumber. And secondly, if you do you can call to explain your diagnosis, the engineer, and he'll make a cup of tea!