Help! My pool pump is not working

Pool pumps can sometimes have problems. In fact, one of the biggest questions we asked: "How do I get my pump to work again not absorb water." If the pump does not work you have to go step by step in diagnosing it. There are two general reasons for these problems: mechanical or physical.

The mechanical reasons are fairly easy to diagnose. Turns on the pump? Otherwise, it could be one of several reasons. First of all make sure it's plugged inthe power switch is on and if it is connected to a timer (good idea to save money), make sure you are in the "ON"-zone.

Hose Timer

Next, check the wiring. If the wiring is somehow defective due to improper installation of age, will not turn on the pump and motor. It would also be useful, with an experienced local pool service or an electrician to diagnose the problem. If the pump more than 5-7 years old, came at the end of its useful life and mustbe replaced. Electric motors do not last forever.

WARNING! When working on or testing of the electric motor, make sure it is connected and not only arrest. You do not want to be hurt by electric shock.

When you turn on the engine and it is buzzing, there are some things to check. First of all, when starting in the spring, it is very likely that some 'of corrosion formed on the magnetic wire. In this case, usually a simple rotation of the crankshaft isRotate the impeller directly (without engine power disconnected) or by removing the rear wall of the electric motor and turning the shaft. After verifying that moves freely and smoothly, put the motor back and turn it on. This heals 95% - 99% of this type of problem.

The physical reasons are sometimes a little 'more time to diagnose the complaint. Here are the questions revolve around him, "not prime the pump" or "the engine is running, but the basket is not full of water" or "thePump works, but it does not draw anything. "

All these questions can be relatively easy to solve and probably do not need to call a professional service. Follow these steps:

Make sure there is enough water in the pool. When the water is not high, a form of "vortex" of the skimmer and the air will be drawn into the system. While in the skimmer, make sure the truck is free of leaves and dirt. If the filter is dirty or in some other way? If so, the backwashSand, DE or change the cleaning cartridge. If the water does not flow through the filter, the pump will not be able to draw water. The use of swimming pools above ground, blown hose, be sure there are no folds in the tube. Underground pool, it is possible that a larger object such as an acorn or bunches of leaves or dead frog or mouse exceed the skimmer basket and constipation is a pipe underground. In this case, a coil may be necessary to remove the object (the least likely to causethis list). Make sure you put the seal pump is clean and well lubricated with good quality silicone lubricant. Clean the dirt particles or sheets. DO NOT use Vaseline or petroleum jelly, both the product reduces the duration of the O-ring seal. Make sure you put the pump cover is not cracked or warped. If so, will not be sealed. Make sure the straps are properly tightened on the pipes (usually above ground pools). Too loose and air will be allowed, in addition to finding leaks. Too tightThe tube and get caught with the same problems. Check all valves leak in general - in particular loss. On the suction side of the pump, have no water leaks when the pump is operating and when turned off, there may be a few drops. Modify or replace the valve seals. At the beginning of each swimming season, you should lubricate the seals and O-rings. Place a drop of silicone Calk around each fillet. Over time can reduce some of the glued jointsso that air can enter the system. Disassemble pump and check that the impeller diffuse or be made (or both). Impellers and diffusers will lead to erosion during the normal time. Worn impeller blades or veins is reduced drastically the amount of water that a pump to move into position. While the pump apart, remove all accumulations of debris from the impeller. Use a wire to clean the areas between the impeller blades. Fragments of leaves, twigs, acorns and seeds, as well as hairthe wheel impede the flow of water will clog, even a couple of tablespoons of debris will make a difference. Do this in mid-season control and able to continue good performance.

The most common causes? Worn or dried and O-rings and the wheels blocked.